Choose language
  1. Home
  2. Edit
  3. Increase Volume

Increase volume of audio

Make a quiet recording, song or video sound louder. A built-in limiter stops loud peaks from distorting, so you can boost more safely.

Loading the tool…
Rate this tool
No ratings yet. Be the first.

How to use

  1. Step 1

    Open a file

    Drop an audio or video file on the page, choose it, or record.

  2. Step 2

    Set the boost

    Raise the gain in decibels while the file plays. Keep the limiter on to prevent distortion.

  3. Step 3

    Compare

    Switch between the original and the louder version to check that it still sounds clean.

  4. Step 4

    Download

    Save the louder file as MP3, WAV, M4A or another format.

Why simple volume boosts distort

Digital audio has a hard ceiling, called 0 dBFS. A sample cannot be louder than this. When you increase the volume of a file whose loudest peaks are already near the ceiling, those peaks are cut flat. This is called clipping, and it sounds like crackling or harsh distortion. Many recordings are quiet overall but have a few short peaks, for example a laugh or a drum hit, which reach the ceiling first and prevent a bigger boost.

This tool solves the problem with a limiter. It watches the signal and, only on those short peaks, turns the level down for a moment so they stay under the ceiling. The rest of the audio gets the full boost. The result is louder without clipping. All processing happens in your browser; the file is not uploaded.

How much to boost

GainEffect
+3 dBa little louder, easy to hear
+6 dBclearly louder, about twice the signal level
+10 dBsounds about twice as loud to the ear
+15 to +20 dBfor very quiet recordings; the limiter works hard

With a lot of gain the limiter is active more of the time. Speech still sounds fine, but music may lose some punch, because the difference between loud and quiet parts gets smaller. Raise the gain step by step and compare with the original.

Common problems

  • Noise gets louder too. A boost raises everything, including hiss and hum. Clean the recording with Noise Reduction first.
  • Only one part is too quiet. Select that part in the audio editor and apply gain only there.
  • Several files need the same level. Use Normalize with a loudness target, which brings every file to the same perceived volume.
  • The phone is still too quiet. Small speakers cannot reproduce deep bass. A gentle bass cut and a small boost around 2–4 kHz with the equalizer makes speech sound louder on phones.

Typical situations

  • Quiet voice message or interview: +10 to +15 dB with the limiter on. Speech stays clear even with strong limiting.
  • Old song that is quieter than modern music: +3 to +6 dB keeps the natural dynamics.
  • Lecture recorded from the back of a room: clean the noise first, then boost, then check that the voice does not sound harsh.
  • Sound of a video: drop the video file and make its sound louder. The tool exports the louder sound as an audio file, which you can put back in your video editor.

If the result sounds tiring or flat after a big boost, go back a few dB. A slightly quieter file that sounds natural is usually better than the loudest possible one.

Frequently asked questions

How do I make an audio file louder?

Open the file, raise the gain while it plays, keep the limiter on, compare with the original, and download.

How can I increase volume without distortion?

Use the limiter. It lowers only the short loudest peaks so they do not clip, while the rest of the audio gets louder.

How many decibels should I add?

Try +6 dB first. Very quiet recordings may need +10 to +15 dB. Listen for pumping or dull sound and reduce if needed.

Why is the background noise louder now?

Gain raises everything equally. Use noise reduction before boosting to keep the noise low.

What is the difference between amplify and normalize?

Amplify adds a fixed gain you choose. Normalize calculates the gain needed to reach a target peak or loudness level.

More tools